Cars rev

Recently, the stopping distance of your car has become much longer, and examination showed the minimum allowable thickness of the brake discs. Then you will need, and urgently to replace. Thus, the tools you need: - the lift or pit - Jack - a standard set of tools that should be available at each motorist - consumables and spare parts - a tripod. It bears and assistant. Before we get started, you need to fix stops with both rear-wheel drive car. Now you can loosen the nuts on the wheels and poddomkratit one side of the car. When the machine is raised to the desired level, take a tripod and with her help fix a car located in the position. Remove the wheel. Stupichnuyu surface and caliper clear the dust and dirt (you can not prevent it from entering the bearing). Unscrew six bolts attached the brake disk, by resorting to the help of an assistant, who must hold down the brake pedal and steering wheel, while you will undermine the bolt. Now you can remove by unscrewing the two bolts, brake calipers. Unscrew two screws and remove the caliper bracket, brake pads and pressure spring. Securely fix the hub, so she did not turn until the end unscrew the six bolts securing the brake disc. However, at the hub cap unscrew the six bolts. Remove the hub. So we got to the main thing - lock semiring. Remove and take out of it two goals - a bronze and steel. After that, unscrew the two screws fixing the locking disc. Here you can apply an ordinary Phillips screwdriver. Unscrew the nut of the external support bearing. To avoid damaging the seal, to be very careful to remove the hub from being in her inner bearing and outer bearing clip. Further bring down the disc with the hub using a soft bumper, and a hammer, but do not forget to do all this must also be very careful in avoiding damage to the gland. And now we take the new drive, make sure that the hub and tsentruem. Before you install should be thoroughly flushed all the details in the solarium, gasoline, kerosene, etc. After a full set of brakes and host, spinning six bolts. Hang on the hub and gathering place of the bearing. After squeezing the nuts, put the lid hub, friction, and washers. Install the caliper and new pads, call assistant and compress the brake disk six bolts. Dress the wheel and the same thing to make with the second party.

During the operation of the vehicle over time is inevitable damage to the glass. It can be as serious defects such as chipped and Shcherbina of gravel or small abrasions left by brush washer. But even minor damage to impair the transparency of glass, and hence the visibility for the driver of the vehicle, not to mention the loss of aesthetic appearance of the car. Of course, with small rubs on the windshield can be no problem to pass inspection. However, it must be remembered that even such defects can distract the driver, greatly increasing the burden on the vision, which increases fatigue. A tired and as a consequence, distraction on the road does not bode well. At this point, as they say, no comment. You can certainly approach the problem radically and simply replace the worn and scratched glass. But this path will require substantial financial costs to the same troubles on poor-quality replacement windows in the form of the appearance of leaks, stress cracks, and as a consequence of a much more serious trouble from defective repair of glass. If there is a minimum set of tools and a few hours of free time is absolutely not difficult to solve the problem of scuffs on the glass, it would wish. The process of removing small defects from car windows is called polishing. If the wear deep enough, polishing process is preceded by grinding glass. Polishing involves the following complex operations: the preparation of the glass, causing polishing (grinding), pastes or powders directly polishing the final wash. Getting to work, you must remember that in order to avoid the effect of the wave (or lens) with a windshield is not recommended to remove deep scratches (those that are clearly being felt by touch), and Shcherbina of small stones and gravel. Additionally, all chips must first be repaired, since there is a risk from heated glass polishing process to get out of a crack cleavage. At the stage of preparatory work should wash the car and glass. Cleanliness is a guarantee that in the polishing process appears more scratches from dirt, got on the instrument. Then the car is covered with foil, leaving direct access to glasses, due polishing. With the help of a marker location with injuries mark the back of the glass. The fact that otherwise in the course of work under a layer of a polishing tool to see them will be difficult. The next stage - the application of polishing compound. Ready-made pasta or diluted to a creamy consistency powder is applied to the polished surface, usually an area not exceeding one square meter, as well as on a felt polishing wheel (usually use 3M). After that, proceed directly to step polishing. Sanders kept at a slight angle and lead to a working surface steadily, avoiding strong pressure. To polish does not dry out, you need to periodically moisten it with water from the spray. It is important to remember that can not be used for polishing grinders, because they give too great speed. Once all the windows properly polished, the protective film is peeled off, windows are washed thoroughly, and the marks of bullet was removed with alcohol.